LED street lights are semiconductor lighting lights, which use light-emitting diodes as a light source. Because it is a solid-state cold light source, it has the characteristics of environmental protection, no pollution, low power consumption, high light efficiency, and long life. The difference between LED street lamps and conventional high-voltage nano-lamp street lamps is that the high-power LED street lamps adopt low-voltage DC power supply as their high source, and are high-efficiency white light diodes composed of GaN-based power blue LEDs and yellow phosphors. They are highly efficient, safe, energy-saving, and environmentally friendly. Long life, fast response speed, high color rendering index and other unique advantages, can be widely used in urban road lighting. The outer cover can be made of PC tube, high temperature resistance up to 135 degrees, low temperature resistance up to -45 degrees.High-power LED street lights refer to LED street lights with a power greater than 30 watts;Application places for high-power LED street lights: urban roads, sidewalks, squares, schools, parks, courtyards, residential areas, factories and other places that require outdoor lighting.Advantages of LED street lights:1. The light of the led street lamp is unidirectional, without diffusion, to ensure the light efficiency;2. The unique optical design of the led street lamp irradiates the light to the required area, improves the light efficiency, and achieves the purpose of energy saving3. The light color rendering of LED street lamps is much higher than that of incandescent lamps. The color rendering index of incandescent lamps is about 20, and the color rendering index of LED street lamps is above 80, which achieves the same brightness visually and psychologically. The illuminance of LED street lamps is on average higher than that of incandescent lamps. The lamp is reduced by more than 20%;4. LED street light has a low decay, less than 3% in one year, and it can still meet the lighting requirements for road use after ten years of use;5. The led street lamp has an automatic control energy-saving device, which can achieve the greatest possible reduction in power and save energy under different lighting conditions at different times;6. Long service life, providing 3-5 years of quality assurance;7. The quality is reliable, all components with high braking capacity are used, and each LED lamp bead has a separate overcurrent protection, so there is no need to worry about damage.LED street light technical indicatorsThe current standard of LED street lights is generally 0.48 for the average illuminance of the road surface illuminance uniformity, and the spot ratio is 1:2, which is in line with the road illuminance. In fact, the 1/2 center light class reaches 25LUX, the 1/4 center light intensity reaches 15LUX, the lowest light intensity at 16 meters away is 4LUX, and the overlapping light intensity is about 6LUX. At present, the street lamp lens material on the market is an improved optical material, with transmittance >=93%, temperature resistance -38—+90 degrees, and UV yellowing rate without change for 30,000 hours. It has very good application prospects in new urban lighting. The depth of the dimming, and the color and other characteristics will not change due to dimming. To develop LED street lightings, you should pay attention to the following aspects:★A. The improvement of luminous flux also needs to be further improved from the basic level of high-power LED epitaxial technology and chip technology.The method of making white LEDs at home and abroad is to first place the LED chip on the packaged substrate, bond it with gold wire, and then coat the YAG phosphor around the chip, and then encapsulate it with epoxy resin. The resin not only protects the chip but also functions as a condenser. The blue light emitted from the LED chip hits the surrounding phosphor layer and is scattered and reflected and absorbed many times, and finally emitted to the outside. The peak of the spectral line of the LED (blue) is at 465 nm, and the half-value width is 30 nm. Part of the blue light emitted by the LED excites the yellow YAG phosphor layer, causing it to emit yellow light (peak value is 555nm), part of the blue light is emitted directly or after reflection, and the light that finally reaches the outside is blue and yellow light, that is, white light. FlipChip technology (FlipChip) can get more effective light emission than traditional LED chip packaging technology. However, if a reflective layer is not added under the electrode of the light-emitting layer of the chip to reflect the wasted light energy, it will cause about 8% of light loss. Therefore, a reflective layer must be added to the bottom plate material. The light on the side of the chip must also be reflected by the mirror surface of the heat sink to increase the light output rate of the device. In addition, a layer of silicone material should be added between the sapphire substrate (Sapphire) of the flip chip and the bonding surface of the epoxy resin light guide to improve the refractive index of the light emitted by the chip. Through the improvement of optical packaging technology, the light extraction rate (luminous flux) of high-power LED devices can be greatly improved.★B. Optimizing the design of LED lighting equipment to improve the quality of use of LEDs. Therefore, it is particularly urgent to study the secondary optical light distribution design of high-power LED light sources to meet the light distribution needs of large-area projection and flood lighting. Through the secondary optical design technology, the design of additional reflecting cups, multiple optical lenses and aspheric light-emitting surface can improve the light extraction efficiency of the device. The traditional light source irradiation direction is 360°, the lamp relies on the reflector to reflect most of the light to a specific direction, only about 40% of the light reaches the road directly through the glass cover, and the other light is projected out of the lamp through the lamp reflector. , The efficiency of the reflector of the lamp is generally only 50%~60%, so about 60% of the light output is in the lamp, which is projected on the road after a loss of 30%~40%. A large part of the light output of the light source is limited to the internal heating and consumption of the lamp. Most of the light of the LED lamp is front light, which can achieve >95% luminous efficiency. This is one of the important characteristics of LEDs that distinguish it from other light sources. If this characteristic cannot be used well, the advantages of LEDs will be great. discount. Since most high-power LED lights are assembled with multiple LED chips, we need to illuminate so many light sources in different directions. We give full play to the characteristics of the chip's overall package and use lenses to solve it. Through optical design, it is equipped with different convex curves according to different needs. , Relying on the lens to distribute the light to different directions, to ensure that the large angle of light can reach 120°~160°, and the small one can concentrate the light within 30°. Once the lens is finalized, the same kind of lamps can be guaranteed under the premise of the production process. The light distribution characteristics of the two have reached the same level. It is completely possible to make LED street lights meet the batwing light type required by road lighting standards through repeated trials and continuous summing up of experience. Tunnel lights, street lights and general lighting have reached the lighting requirements of their respective application places.★C. Heat dissipation is a key problem that LED street lights need to solve.As we all know, LED is an optoelectronic device. During its working process, only 15% to 25% of the electrical energy is converted into light energy, and the rest of the electrical energy is almost converted into heat energy, which increases the temperature of the LED. In high-power LEDs, heat dissipation is a big problem. For example, if a 10W white LED has a photoelectric conversion efficiency of 20%, 8W of electrical energy is converted into heat. If no heat dissipation measures are taken, the core temperature of the high-power LED will rise rapidly, when its junction temperature (TJ) When the temperature rises above the maximum allowable temperature (usually 150°C), the high-power LED will be damaged due to overheating. Therefore, in the design of high-power LED lamps, the most important design work is heat dissipation design. Due to the high brightness requirements of LED street lights, the use environment is relatively harsh, if the heat dissipation is not solved well, it will quickly cause LED aging and decrease stability. A street lamp using 250W high pressure sodium lamp, due to mature technology and good heat dissipation control, even if it works for 5000 hours, the light decay is still very small. High-power LED street lights under the same conditions, if the heat dissipation is not solved well, the light decay will be great. The heat dissipation methods of LED street lights mainly include: natural convection heat dissipation, additional fan forced heat dissipation, heat pipe, loop heat pipe heat dissipation, and uniform temperature plate heat dissipation. The forced heat dissipation method of installing a fan has a complicated system and low reliability, and the heat dissipation method of heat pipe and uniform temperature plate is costly.★D. LED street lights will eventually choose modular installation and maintenance.The most high-pressure sodium lamps used on the road, the internal ballasts and other components are not easy to damage, most of the reason for not lighting is the damage of the light source, the maintenance method only needs to replace the light source. A skilled operator can perform high-level operations personally. However, LED street lights have many internal components. Except for the light source (chip), damage to other parts will cause the chip to not light up. Therefore, at the scene, it is impossible to immediately determine the cause of the damage to the LED street light. If the LED street light does not light up, the LED street light needs to be taken off and shipped back to the factory for various tests. This way of replacing LED street lights is very cumbersome. The final version of the development of LED street lights is to develop into modularity. The light source, electricity, etc. are all replaced in accordance with the plug-in connection, so that a skilled worker can fully independently judge the cause of the damage and perform on-site maintenance

LED street lighting has been basically mature after many years of application technology accumulation. It has already been applied on a large scale in the lighting industry and has entered a period of rapid development. However, many users say that LED street lights are not easy to use because they have stroboscopic problems, but the reason for this may be product quality problems or improper use.Stroboscopic is to watch the screen of another electrical appliance on the screen of one electrical appliance. A bright line on the screen of another electrical appliance will move from the bottom of the screen to the top, and then appear from the bottom. Turn on the phone camera mode and aim the lens at the LED street light on the side of the road, and you can find that there is a "ripple" phenomenon in the phone camera, which is "stroboscopic". Almost all types of lights are prone to flicker, including incandescent, halogen, and even LED lights. But the effect of each light is different. For example, in incandescent lamps and halogen lamps, the filament temperature reacts slowly to changes in current, so the flicker effect is not noticed. For the current changes, the LED responds almost immediately, so the flickering will be more noticeable. If the LED lamp is driven with an over-temperature protection function, and the heat dissipation performance of the material of the lamp cannot meet the requirements, the over-temperature protection of the drive will flash and go out when it starts to work.We can analyze the causes of LED street lights stroboscopic according to several methods as below：First of all, confirm whether the driving voltage and current required for the series and parallel number of the lamp LED are within the nominal range of the output parameters of the LED driving power supply. If it exceeds the nominal range, it may cause the lamp to flicker.Secondly, confirm the wiring voltage drop range in the entire LED lighting street lamp circuit, that is to say, measure the actual voltage of the lamp bead string farthest from the LED drive power supply, plus the wiring voltage drop should be within the highest output voltage range of the LED drive power supply Inside, if the maximum output voltage of the LED driving power supply is exceeded, it will cause the light to flicker.Once again, confirm that the working environment of the outdoor LED street light power supply is in line with the requirements of its manual, such as the range of input AC voltage, too high or too low input voltage will trigger the undervoltage and overvoltage protection of the LED driving power supply; the working environment temperature has been The heat dissipation environment, the working environment temperature is too high or the heat dissipation environment is not ideal, such as airtightness, poor air circulation and other heat dissipation environments may trigger the overheat protection circuit of the LED driving power supply and cause the lights to flicker.Finally, confirm whether the control system or dimming system matches the LED street lamp power supply. Different control systems or dimming systems have different requirements for the LED drive power supply. The main thing is to pay attention to the agreement of the control port and the voltage amplitude of the dimming port. Value, frequency, compliance of the interface.In theory, all light sources that use alternating current have stroboscopic flashes, and LED lights are naturally no exception. As the main outdoor lighting fixtures, street lights can easily make it difficult for the surrounding residents to fall asleep, leading to insomnia and other symptoms. Some people think that "outdoor lamps do not require too much strobe flashing, it's almost the same." In fact, drivers or residents have been exposed to poor lighting conditions for a long time, which is harmful to the eyes and body. However, we can change the ordinary alternating current stroboscopic frequency into a higher stroboscopic frequency through a special device. Although the stroboscopic frequency still exists, it can achieve the effect of nearly no stroboscopic, reduce the impact on the human eyes, and protect the eyes The role of the body. This requires the customer to reach an agreement with the manufacturer in advance to find a suitable solution.

Why are the solar street lights on the domestic market the same in terms of wattage, weight, and configuration, some manufacturers' solar street lights are very cheap, and some of the prices make us feel that they are really ridiculously low? Many customers are easily lost in the price and feel that our price is too expensive. However, some customers will find us again for purchase later, saying that those solar street lights with ultra-low prices are basically unusable, so what are the improper operations of these manufacturers with ultra-low prices?According to the actual material, no matter how the province is calculated, solar street lights will not have such a low price, but some manufacturers just use the price to attract customers, one is to cut corners on the product parameters. For example, for solar panels, some customers configure 60w, then the manufacturer will reduce the 60w to 50w, 40w, or even 30w for assembly, so it is difficult for laymen to see it; the second is the false standard of solar batteries. Can not meet the original quality standards; third is the use of old recycled batteries, which have poor durability and very short life; Fourth, the wall thickness of the light pole cannot meet the requirements, which is unsafe; It should have used integral hot-dip galvanized materials and cheap solar street lights which is made directly with galvanized sheet, and it will rust in less than 3 months.The price of such a solar street lamp may be liked by many consumers, but the quality and service life problems it brings are by no means what customers want to see. The solar panels and battery capacity are not up to the standard. Doesn't light up. Therefore, the price of solar street lights is not as low as possible. We must purchase according to actual needs and carefully confirm the parameter requirements. It is recommended to choose an old brand manufacturer, so that the quality and after-sales are well guaranteed. CHZ Lighting is a manufacturer of LED lamps that has been focusing on outdoor lighting for 12 years. We only make reassuring products and provide conscientious prices.

Recently, CHZ Spain branch completed a courtyard lighting renovation project in a small town. Located in the Barcelona region of Spain, the town is one of the eight satellite cities of Barcelona and attracts a large number of tourists every year. In order to revive the urban tourism industry after the epidemic, the city government decided to renovate the courtyard lighting in the town.Previously, the classic garden lights were used, and all high-pressure sodium lights were installed, which not only had low brightness, but also had poor color rendering. After our Spanish team studied this project, we decided to use our GD01A LED courtyard lamp to participate in the bidding for this project. It stood out among many competitors (including PHILIPS, THORN, LANDVANCE and other brands) and got this project.     This courtyard lamp is a classic lamp specially developed by us for the European market. It uses LUMILEDS3030 or 5050 high-efficiency lamp beads and MW (0-10V+timing dimming) drive to achieve high efficiency and energy saving. The height of the light pole is generally 4~5 meters. We use 60W power and a color temperature of 4000K, which improves the light efficiency and color rendering. For the courtyard lights on the side of the road, we use TYPE II lenses; for the courtyard lights on the square, we use TYPE V and 120° lenses to achieve the corresponding lighting effects. Our team spent nearly a week on site design and construction, and successfully completed the lamp replacement work.  After the test, after on-site data collection, the test results are also satisfactory. The average illuminance reaches 45LX, which is 30% higher than the previous HID, and the power consumption is only 50% of the previous. The owner feels very satisfied with this effect.Our company has accumulated rich experience in municipal roads, and also trained a professional team, so that our brand has a high reputation and good reputation in the local area. I hope that our Spanish team will continue to work hard, get more projects, and contribute more wisdom and strength to the construction of beautiful cities in Spain.